System Error 3043: PERR: Position Error!{Axis}

Post Reply
ktd-cmm
New User
New User
Posts: 1
Joined: Sat Aug 19, 2017 9:25 am

System Error 3043: PERR: Position Error!{Axis}

Post by ktd-cmm » Sat Aug 19, 2017 9:33 am

We are receiving this error when trying to move in any axis. Started in the middle of a program. Steps we've tried. Shutdown, checked for oil, scale readers all have green lights. Flags error during home procedure or with any motion.

User avatar
medupriest
Moderator
Moderator
Posts: 411
Joined: Fri Mar 13, 2015 11:59 am

Re: System Error 3043: PERR: Position Error!{Axis}

Post by medupriest » Mon Aug 21, 2017 9:26 am

This will be an error from the controller. How are the air levels? We can also take a look at a log file. I will PM you an email address to send the log file to.

fgalego
New User
New User
Posts: 1
Joined: Tue Sep 26, 2017 12:48 pm

Re: System Error 3043: PERR: Position Error!{Axis}

Post by fgalego » Tue Sep 26, 2017 12:51 pm

Having similar issue. Did not find an solution on this forum.
Machine stops all of a sudden and gives error PERR: Position error![X AXIS]
Machine becomes very rigid and not even able to move by hand. Machine will not home.

User avatar
CrashN8
Site Admin
Site Admin
Posts: 375
Joined: Thu Feb 09, 2017 4:07 pm

Re: System Error 3043: PERR: Position Error!{Axis}

Post by CrashN8 » Tue Sep 26, 2017 1:21 pm

Sounds to me that Air Pressure has dropped below the acceptable limit. If the air is ON but the servos are engaged, you should still be able to move the machine just with resistance of motors. However if compressed air is not on then you won't even budge the machine in any axis.

enpalani
Power User
Power User
Posts: 79
Joined: Thu Aug 01, 2013 11:44 pm

Re: System Error 3043: PERR: Position Error!{Axis}

Post by enpalani » Wed Sep 27, 2017 12:24 am

If not able to move by hand, the problem is either less pressure(due to tube bend or air regulator problem) or air bearing struck in specific axis.

ken60
Frequent User
Frequent User
Posts: 63
Joined: Fri Mar 21, 2014 12:32 pm

Re: System Error 3043: PERR: Position Error!{Axis}

Post by ken60 » Thu Sep 12, 2019 10:51 am

I have this error today, air pressure level checked normal. Restart computer, cmm and controller did not help
Metris CMM
3.7 sp2 CMM Manager
PH10
LK Direct DCC

User avatar
007tda
Nikon
Nikon
Posts: 8
Joined: Thu May 03, 2012 3:08 pm

Re: System Error 3043: PERR: Position Error!{Axis}

Post by 007tda » Thu Sep 12, 2019 4:07 pm

Is this error showing up right away when you try to home it out, or after it homes and you are moving it around?

ken60
Frequent User
Frequent User
Posts: 63
Joined: Fri Mar 21, 2014 12:32 pm

Re: System Error 3043: PERR: Position Error!{Axis}

Post by ken60 » Thu Sep 12, 2019 7:27 pm

The error occur Before it home, while it is homing, after it homes, short distance and long distance with joy stick you name it. Also, now sometime while the machine idle the probe head on screen jumping back and forth along y-axis for a while then stop

Post Reply