Machine Setup -Table Height

ameade022008
Power User
Power User
Posts: 76
Joined: Thu Oct 03, 2013 12:48 pm
Location: Tempe, AZ
Contact:

Re: How to set table height in CMM Mgr v3.7+ with UCC Server

Post by ameade022008 » Thu Feb 01, 2018 4:04 pm

Ryan Christopher wrote:The advanced tab needs to be active in UCC Server to do this...

1. Right click over MACHINES > ~machine name~ > EQUIPMENT > CMMBed
2. Use the Locate Bed action from the tree to update the table position in UCC Server.
3. Go back to CMM Manager and Sync from the Probes tab of the ribbon.
UCC Server LOCATE BED.jpg

What version of UCCserver are you on?

I know I had some other conflict issues with UCCserver bugs being fixed in later versions of V5+
Albert Meade
Quality Manager, Metalcraft Inc.
http://azmetalcraftinc.com/

User avatar
Ryan Christopher
Nikon
Nikon
Posts: 245
Joined: Mon Jun 06, 2011 3:00 pm
Location: Sumner Washington
Contact:

Re: Machine Setup -Table Height

Post by Ryan Christopher » Thu Feb 01, 2018 4:16 pm

Good catch...I just updated to 5.0.5 so that's why I haven't been able to test it out until now. You'll know somethings up when you see that CMM Manager sees RefTool as a separate probe assembly that contains RefTip.

The release notes...
"
UCC I++ Full Synchronization
- Full synchronization of probe heads, probe assemblies, tips, calibration spheres,
machine limits, table position for UCC Server version 5.0.3 and above.
- Configuration of probes is no longer required and allowed in CMM-Manager.
- Recalling probe assemblies by name is added and must be used for I++ systems,
and as a result, program migration is needed for I++ systems
- An I++ migration tool is added.
"
Ryan Tackes
Applications Manager, VMS Inc.
http://www.vantagemeasure.com/

ameade022008
Power User
Power User
Posts: 76
Joined: Thu Oct 03, 2013 12:48 pm
Location: Tempe, AZ
Contact:

Re: Machine Setup -Table Height

Post by ameade022008 » Fri Feb 02, 2018 10:23 am

I am on 4.9.4
Albert Meade
Quality Manager, Metalcraft Inc.
http://azmetalcraftinc.com/

ameade022008
Power User
Power User
Posts: 76
Joined: Thu Oct 03, 2013 12:48 pm
Location: Tempe, AZ
Contact:

Re: Machine Setup -Table Height

Post by ameade022008 » Fri Feb 02, 2018 11:25 am

This is How my UCC server looks now. But after a sync 3.7 is still way off
UCC SERVER TABLE.JPG
3.7:
CMM 3.7 table.JPG
You do not have the required permissions to view the files attached to this post.
Albert Meade
Quality Manager, Metalcraft Inc.
http://azmetalcraftinc.com/

User avatar
Ryan Christopher
Nikon
Nikon
Posts: 245
Joined: Mon Jun 06, 2011 3:00 pm
Location: Sumner Washington
Contact:

Re: Machine Setup -Table Height

Post by Ryan Christopher » Fri Feb 02, 2018 12:23 pm

I was on UCC Server 4.9 before last week and It didn't sync right either. Everything worked ok but the table didn't look right.

It sounds like the sync behavior isn't supported unless you have 5.0.3 or greater. Upgrading the UCC Suite is a task you will need help with. Make sure you get help from your service provider or Renishaw.
Ryan Tackes
Applications Manager, VMS Inc.
http://www.vantagemeasure.com/

ameade022008
Power User
Power User
Posts: 76
Joined: Thu Oct 03, 2013 12:48 pm
Location: Tempe, AZ
Contact:

Re: Machine Setup -Table Height

Post by ameade022008 » Fri Feb 02, 2018 3:49 pm

Yeah the issue has been going on since October, I just had my annual calibration in January and was told they would fix it then, but the tech never updated it.
Albert Meade
Quality Manager, Metalcraft Inc.
http://azmetalcraftinc.com/

Post Reply