Search found 422 matches

by medupriest
Mon Jun 17, 2019 10:20 am
Forum: Advanced Programming
Topic: Reporting Multiple single segment Feature control frames
Replies: 4
Views: 2388

Re: Reporting Multiple single segment Feature control frames

Composite position is located in the report ribbon tab as shown below.
Untitled.png
by medupriest
Fri Jun 14, 2019 11:24 am
Forum: Advanced Programming
Topic: GD&T Position Feature
Replies: 4
Views: 1529

Re: GD&T Position Feature

The diameter is correct, but the position is off. You receive bonus tolerance because the diameter is over the low limit.
by medupriest
Thu Jun 13, 2019 2:35 pm
Forum: General Application Support
Topic: Joystick Control After "unexpected Touch"
Replies: 5
Views: 1657

Re: Joystick Control After "unexpected Touch"

This can be cause by a stylus that is too heavy for the strength of the module. You may also try turning down your machine's acceleration.

Is this a new install? Had the machine been functioning recently? If so, What changed?
by medupriest
Wed Jun 12, 2019 9:54 am
Forum: Advanced Programming
Topic: Projecting Measured Point
Replies: 7
Views: 1914

Re: Projecting Measured Point

if you construct a point at the centroid of the feature, then right click on that construction and select "Transform". Then you can enter in the angle of rotation, select the current reference frame, and select make 1 copy.
by medupriest
Mon Jun 10, 2019 2:02 pm
Forum: Alignments
Topic: Move Part with Fixture in CAD
Replies: 4
Views: 1565

Re: Move Part with Fixture in CAD

I would just add it to furniture for the writing of the program for the collision-free paths, then delete the furniture so it isn't in your other programs.
by medupriest
Mon Jun 10, 2019 12:51 pm
Forum: Alignments
Topic: Move Part with Fixture in CAD
Replies: 4
Views: 1565

Re: Move Part with Fixture in CAD

Furniture will show up in all programs. Move Part will move both CAD entities and we only allow for one CAD reference frame. You could launch the op 2 program from the first program and just have the CAD model in the proper orientation for that side. After writing creating the paths, you could also ...
by medupriest
Fri Jun 07, 2019 11:41 am
Forum: Advanced Programming
Topic: GD&T Position Feature
Replies: 4
Views: 1529

Re: GD&T Position Feature

The feature report you should have so you can report the diameter.

You do not necessarily need the cord dev. or the show tolerances. In most cases, those would not be shown in a report going to the customer.
by medupriest
Fri Jun 07, 2019 11:39 am
Forum: Advanced Programming
Topic: GD&T Position Feature
Replies: 4
Views: 1529

Re: GD&T Position Feature

You have MMC (maximum material condition) selected for the material modifier. This should be set to RFS (regardless of feature size) instead. Everything else looks correct to me. You can change the datums so they are A, B, C from top to bottom. With the "use current ref. frame" option selected, it i...
by medupriest
Wed Jun 05, 2019 1:08 pm
Forum: General Application Support
Topic: Application Error 0x000007b
Replies: 2
Views: 1240

Re: Application Error 0x000007b

Can you provide a windows process dump? Instructions of how to do so can be found at the following link https://support.kaspersky.com/common/diagnostics/12401.
by medupriest
Mon Jun 03, 2019 10:40 am
Forum: Tutorials and Training Guides
Topic: Solved- Running a Program - what really happens?
Replies: 14
Views: 11849

Re: Solved- Running a Program - what really happens?

The Sync CAD is the Command you want. You only need to have it in place after the DCC alignment.

The CAD model must be in sync when you do Cloud-to-CAD reporting as it is using the part reference frame and comparing to the CAD nominals (unless you are using best-fitting).