Search found 314 matches

by CrashN8
Thu May 23, 2019 12:06 pm
Forum: Program / DCC Settings
Topic: How to change DCC settings
Replies: 1
Views: 18

Re: How to change DCC settings

Program Settings... It's the First operation in every program, put there automatically when you create new file. Also, can be added to any program from Ribbon Tab Features>Teach>DCC Settings.
by CrashN8
Thu May 23, 2019 12:04 pm
Forum: Advanced Programming
Topic: Batch Run For Repeatability Study
Replies: 6
Views: 40

Re: Batch Run For Repeatability Study

If you save and then recall the SAME Fixture Alignment then, yes I would expect the behavior that you describe. Fixture Ref Frame should be reserved for Recall at beginning of program only. Also, note you can skip initial steps of program for Batch Run if needed.
by CrashN8
Thu May 23, 2019 12:02 pm
Forum: Reporting
Topic: How to properly report Cloud to CAD.
Replies: 5
Views: 1259

Re: How to properly report Cloud to CAD.

Nothing to do with Alignment... Everything to do with fact that CMM can NEVER measure the same points twice in the exact same spot. Nominal Value for each point comparison is adjusted according to nearest location of NOMINAL CAD to ACTUAL point. Every time the program runs, the CMM measures the poin...
by CrashN8
Wed May 22, 2019 5:05 pm
Forum: Advanced Programming
Topic: Batch Run For Repeatability Study
Replies: 6
Views: 40

Re: Batch Run For Repeatability Study

What kind of system? DCC CMM, Manual CMM, Vision system, what controller, what probing, etc.

Does it repeat if you run the program individually or is this truly isolated to Batch Run?

Can you send the program and results to Help Desk?
by CrashN8
Wed May 22, 2019 9:28 am
Forum: General Application Support
Topic: Probe Comp turned off.
Replies: 3
Views: 113

Re: Probe Comp turned off.

Probe Comp for manual and non-CAD measured points is OFF by default. I think ON for CAD based point measurements... The theory is that without CAD or at least good idea of the surface vector it's safer (more accurate) to measure with no comp. Please note that report 'distance between' operation has ...
by CrashN8
Tue May 21, 2019 4:37 pm
Forum: General Application Support
Topic: SHOP FLOOR LAUNCHER
Replies: 1
Views: 18

Re: SHOP FLOOR LAUNCHER

Change your primary monitor in WIndows... SFL is drawn over entire "Primary" monitor / display. Run CMM-Manager once on Primary monitor and then both should be displayed on same monitor indefinitely. Also, check the options in Preferences for General Permissions.
by CrashN8
Mon May 20, 2019 9:27 am
Forum: General Application Support
Topic: Feature Suggestion - Transform / Copy
Replies: 1
Views: 24

Re: Feature Suggestion - Transform / Copy

We've already added the "Copy" Transform option that you mention - i.e. user can specify number of copies that will be translated and/or rotated. This was added in version 3.6. I will add the request to highlight features in Main Graphics too. Thanks for the input.

x_form_copy.jpg
by CrashN8
Mon May 20, 2019 9:19 am
Forum: Reporting
Topic: How to properly report Cloud to CAD.
Replies: 5
Views: 1259

Re: How to properly report Cloud to CAD.

No actually the nominal value is not a discreet XYZ point but actually a 3D CAD surface... SO this means the nominal XYZ point changes from one program execution to the next due to small position deviations attributed to CMM motion. Think instead of a manual CMM... How would the user ever take point...
by CrashN8
Fri May 17, 2019 9:58 am
Forum: Probe Racks
Topic: Locating rack
Replies: 3
Views: 2570

Re: Locating rack

I got an unexpected touch after unloading the stylus. Did you get that error due to safe position? I am trying to setup a new rack on my machine and I got the error. I am thinking of the safe position too Are you using Mitutoyo CMM? If so, please see post here with details about Probe Inhibit for d...
by CrashN8
Fri May 17, 2019 9:54 am
Forum: Helmel
Topic: CMM-M install on Win 7 64 Bit computer problem
Replies: 1
Views: 61

Re: CMM-M install on Win 7 64 Bit computer problem

I think AE from Helmel is already working with you on a solution... I see that Helmel CMM was tested in 64bit version for CMM-Manager 3.8 (first release of 64bit version) but we have made some small tweaks to this driver recently that will be included in 3.9. I suspect you are the customer that Helm...