Search found 81 matches

by enpalani
Wed Jan 29, 2020 1:03 am
Forum: Reporting
Topic: Actual value not proper in report during program run mode
Replies: 2
Views: 349

Re: Actual value not proper in report during program run mode

Admin,

Please give the solution for above. We need to measure more than 100 components and submit reports.
awaiting for solution.

Thanks
by enpalani
Wed Oct 23, 2019 4:58 am
Forum: Reporting
Topic: CONCENTRICITY between CIRCLE to CIRCLE-calculation reg.
Replies: 1
Views: 538

CONCENTRICITY between CIRCLE to CIRCLE-calculation reg.

Hello,

Here I had enclosed program and report file for your reference.
Please clarified the calculation(software how arrived) of CONCENTRICITY between CIRCLE to CIRCLE.
Note: Circle x & y offset value is high but concentricity value is small. please refer attached reports.
by enpalani
Tue Mar 05, 2019 7:46 am
Forum: Gear Inspection
Topic: reg. how to measure Impeller
Replies: 1
Views: 1311

reg. how to measure Impeller

Impeller.pdf
Here with I enclosed Impeller drawing.

Is this part measure with GEAR or SCANNING pack?.

Note: I have PH20 with CMM M.

please suggest.
by enpalani
Wed Jan 02, 2019 5:48 am
Forum: SP25 Scanning
Topic: How To: 2D Cloud Scan
Replies: 2
Views: 4660

Re: How To: 2D Cloud Scan

Is possible to construct feature from cloud specific point not total cloud?. I need to construct circle and arc from some portion of cloud.
Any suggestion...
by enpalani
Sat Aug 18, 2018 1:55 am
Forum: General Application Support
Topic: windows updates cause of problem
Replies: 2
Views: 1886

Re: windows updates cause of problem

Yes, this issue faced our customer. we advise our customer to restore one week before backup,then working. Now advise customer to do not update.

Hardware is Renishaw UCC T3 PLUS.
by enpalani
Sat Mar 10, 2018 2:26 am
Forum: PH20 / I++
Topic: Questions: upgrade Renishaw UCC server software.
Replies: 1
Views: 2909

Re: Questions: upgrade Renishaw UCC server software.

Hi,

UCCsuit 4.9.4 is the best version of both UCC2 and UCC2-2.

As per RENISHAW notes
"You cannot use 5.0 and above version of software with old UCC2 controllers for the Revo, Revo-2 or PH20 heads. The UCC controller must be at least a UCC2-2 for these heads to work correctly. "
by enpalani
Mon Dec 18, 2017 7:43 am
Forum: Reporting
Topic: Distance between constructed two lines from plane
Replies: 1
Views: 2644

Distance between constructed two lines from plane

[1] Measured two parallel plane and top of one plane. [2] reported distance between two parallel plan. Value is around 15.05mm [3] I have moved top plan to bottom side 10mm for construct line intersect top and parallel planes. [4] then check the distance between constructed two lines(top and paralle...
by enpalani
Wed Sep 27, 2017 12:24 am
Forum: Off Topic
Topic: System Error 3043: PERR: Position Error!{Axis}
Replies: 7
Views: 6307

Re: System Error 3043: PERR: Position Error!{Axis}

If not able to move by hand, the problem is either less pressure(due to tube bend or air regulator problem) or air bearing struck in specific axis.
by enpalani
Fri Jul 28, 2017 2:14 am
Forum: Off Topic
Topic: LICENCE from one PC to another PC -Procedure
Replies: 2
Views: 3722

LICENCE from one PC to another PC -Procedure

What is the procedure to change CMM M software LICENCE from one PC to another PC
by enpalani
Thu Nov 10, 2016 5:53 am
Forum: PH20 / I++
Topic: PH20MT & UCC MT5 Support
Replies: 6
Views: 6108

PH20MT & UCC MT5 Support

Is CMM M supports with Renishaw PH20MT probe head and UCC MT5 controller? is any customer used this configuration?